MiniTioune V0.9 beta optimised for QO-100

Quote from ik4idy

Hi JP,

in these days I tested new version in my Minitioune Express HW.

Unfortunately V 0.9 Version cannot decode at 125 K/s, 333 K/s. The old version decode these speed toghether without problems. May be something wrong in the new sw or may be my hardware has some issues ?

73 de Alessio

Display More

-SEE LATER POST ABOUT THE CURE FOR MY PROBLEM-

I have the same problem!! I also think it might have worked at first but cannot be sure.

I attach two screen shots. One using V8 and one using V9. Both receiving (or not ) the same signal. Yes the signal was the same.

I suggest to put the new version in a different folder from the previous versions and to use only the minitiouneConfig.ini file of the latest version.

Quote from I0LYL

I suggest to put the new version in a different folder from the previous versions and to use only the minitiouneConfig.ini file of the latest version.

Thanks IOLYL, but that was not the problem. The problem was the offset frequency of the LNB was way off. When I used the new V9 software I used the Adapt Offset button on the beacon and keep it tick. After that the smaller SR signals were lost!! I found the answer when another station suddenly transmitted on the frequency I was actually tuned to!! Reloading the software again made it all work.

So if you get this 'fault' check the offset and if that does not work reload the program again overwriting the old files.

Martin

Quote from I0LYL

I suggest to put the new version in a different folder from the previous versions and to use only the minitiouneConfig.ini file of the latest version.

The Sw is in two separate folder, in my case, but in my opinion this not represent the focus.

First of all I've some doubt on the correct pointing of my dish. but comparing signal form batc Wb spectrum and my SDR, i found the same signals. Yes Express is a hardware very different from other models of Minitiotune, the critical point may be the temperature. It's my aim to modify the Express for the 5 V supply. This mods is described clearly on the manual provided. It's quite complex to do due SMD, but not a mission impossible. If this way fail I'm ready to buy another and I hope more efficient hardware.

Alessio, which version do you have the A or the B?

I have the B and I have no problem even with weak signals.

also 125

Hi Lucio,

I'm using the same version (B iI suppose but where is the evidence ?), still having issues with Mititioune express HW. I'm fighting a lot to have a best results, I can decode only down to 1 M/s, below it's impossibile. I downloaded the version :

MinitiouneV09beta8_9 package.zip

73 vy best

ik4idy I have it running here...works fine.. maybe you have to reset your equipment it should work..

Quote from ik4idy

Hi Lucio,

I'm using the same version (B iI suppose but where is the evidence ?), still having issues with Mititioune express HW. I'm fighting a lot to have a best results, I can decode only down to 1 M/s, below it's impossibile. I downloaded the version :

MinitiouneV09beta8_9 package.zip

73 vy best

Display More

Alessio, rev B does not require HW modifications.

Page 29 manual.

https://www.datv-express.com/u…%20User-Guide-draft16.pdf

Quote from I0LYL

Alessio, rev B does not require HW modifications.

Page 29 manual.

https://www.datv-express.com/u…%20User-Guide-draft16.pdf

Visto, stasera provo. Grazie.

I belive to have the same issue.

Looking forward for a manual

73 Thanks

Regards

Okay, with the suggestion of JP I have been modified the LO ref. The procedure that I have been used is to, increase and decrease, by some try, the main frequency. I found good rx at 333 K/s decreasing 40 KHz. This difference is now applied to the LO, in main screen. Inserting now the real frequency (From BATC Spectrum WB) the Minitioune locks the signal. Now I will need to try with more lower rates.

More test will be done. Stay tuned.

73

MiniTiouner V2 great author F6DZP Jean Pierre of his project and the new program version 9 is not difficult to instill just understand the function of its configuration MiniTioune_software of the various tests 73 IK1HGI Tony

Hello Jean-Pierre,

your Minitioune software is excellent. Thank you very much for your great
service to the QO-100 community.

Do you plan to implement also a "dual window" version to support
watching 2 DATV signals simultaneuosly with the new Minitiouner Pro V2 ?

Alternatively do you recommend to run 2 instances of the Minitioune

software to access both USB output signals from the Minitiouner Pro V2 ?

Kind regards

Matthias DD1US

http://www.dd1us.de

Hi a good initiative I tried a duplex program using the MiniTioune software on the installed UDP configuration and ANDRESS Local to be able to receive the same PC on two VLC or OBS programs only an active program, with the same system also a test run on the other PC win7 excellent 32-bit results if you want to use the system as a trial version of a local IP network send the TS sent here the IP you use to send: localIP this is useful in case you have several local networks like a home wifi network for Internet and a local ethernet network 73 ik1hgi Tony

METTERE SOLO SE AVETE VERIFICATO L'IP DI CONNESSIONE DELLA RETE

; Indirizzo UDP per trasferire TS

; Indirizzo UDP per trasferimento TS

; .....................................

; Indirizzo UDP per TS

; TS_AddrUDP = 230.0.0.10

; puoi provare un indirizzo virtuale se non hai una connessione Ethernet o Wifi

; TS_Port = 10000

;
TS_Locallip = 192.168.xx.xx

TS_AddrUDP = 127.0.0.1

TS_port = 8888

:

; IP locale usato per inviare il TS

; metti qui l'IP che usi per inviare localIP

; questo è utile nel caso in cui tu abbia diverse reti locali come a casa

; una rete wifi per Internet e una rete ethernet locale

; METTERE SOLO SE AVETE MOLTO VERIFICATO IL TUO IP DELLA CONNESSIONE DI RETE

; TS_LocalIP = 192.168.1.55

;

TS_Localip = 192.168.xx.x x

73 IK1HGI Tony