Is possible mal function of connections grounds in the interior of Pluto? What is your internal cpnexios for GND?
Hello Jabi some colleagues have had problems inserting the firmware 0201, some have found your problem, to others it is blocked and to me it no longer transmitted.
We all solved it by doing the recovery procedure of the pluto by rewriting uboot.dfu and pluto.dfu (fw 0.32 adalm pluto) and then putting back the Evariste firmware and my patch.
I think i have read some messages where it was suggested not to use the fw 0201 for problems it can create.
Many tnx, but .... How is possible find uboot.dfu ?
I am located boot.dfu but no uboot.dfu.
IS0GRB Pluto DATV Patch v.1.5 available
1- Improved operability.
Inserted under the spectrum the "save to flash and "apply settings" buttons to be ready to update the modulator after tuning a signal.
2- Memory for RX / TX flag in spectrum settings
Insert the memory for the status of the rx and tx flags in the spectrum settings.Now updating the page maintains the previously selected state.
3- Added the config section for the ethernet interface
Now it is possible to easily configure the ethernet interface with IP address and Default gateway.
4- Compact all sections.
The controller page is more intuitive and compact.
IS0GRB Pluto DATV Patch v.1.6 available:
1- Added disable option for audio bit rate.
It is now possible to disable audio in the transport stream by selecting "disable" in the audio bit rate drop-down menu.
2- PTT ON / OFF at startup.
Now you can decide whether to set the PTT ON / OFF at startup.
For those who use OBS it can be convenient that the PTT at start-up is OFF, while for those who use the repeater or beacon mode it is necessary that at start-up it is ON for obvious reasons.
3- Checking the beacon.ts file name in the Live & Static beacon configuration.
During the upload the file will be checked and if the name does not match exactly and all lowercase will not be uploaded.
This verification is necessary to eliminate the problems encountered by some.
4- Delete all video files button in Static Beacon section
This button now deletes all video files in the partition that have been uploaded by mistake earlier.
5- Delete all patch button.
The delete all patch button, in the Firmware section, now deletes all the files present in the partition that have been loaded by mistake earlier with the .zip extension and/or with a name different from patch.zip
6- Fixed a small bug in storing the flag of the 4 DATV modes.
Thanks you for the Patch v.1.6 .
Can I suggest to add in MiniTioune Settings for LNB Volts parameter the 0V setting.
I think that I am not the only one to have an active splitter in front of the MiniTioune that already supplies power to the LNB.
73 qro de michel, hb9dug
Hello Michel, thank you for the suggestion.
You can download my patch v.1.62 you will find the change.
Also include v.1.61:
1- Added FFMPEG image fine adjustment
Added the drop-down menu for the custom setting of the precision adjustment on FFMPEG.
Possible choices: film | animation | grain | stillimage | psnr | ssim | fastdecode | zerolatency.
Request from Raffaele IW1QEF & Francesco IT9HZM
IS0GRB Pluto DATV patch v.1.63 available:
1- Inserted PTT delay when switched to Standby.
During the qso, during the net or in local DATV it is always necessary to listen to the last piece of the transmission to avoid detaching the ptt of the Pluto before all the data have been sent and therefore make sure that the correspondent has heard all the words.
Now it is possible to take advantage of a delay in PTT Off (active by default and can be deactivated) which allows you not to worry about playback and to be sure that the PTT is disconnected only after the necessary seconds to empty the buffer.
By default, a 8 seconds delay is selected, suitable for SR333, but can be reduced for high SRs and can be increased for low SRs where the buffer emptying time is greater.
Activating the PTT delay and after pressing SWITCH OFF when the PTT is ONAIR you will see a countdown progress bar that indicates the seconds remaining in Standby
IS0GRB Pluto DATV Patch v.1.7 available
1- Added memories for the modulator.
Now it is possible to configure the memories for the modulator.
The possible operations are: Save, Delete, Modify label, Delete all memories, Backup and Restore of the memories
Clicking on the delete and modify buttons, suggestions for how to operate will appear.
Also included the double confirmation when you decide to delete all the memories, even if the restore will be quick and easy with the backup file previously saved.
IS0GRB Pluto DATV Patch v.1.71 available
1- Inserted the colors for the memories.
For a better organization and identification it is now possible to associate a color to the memories during the store that can be modified later clicking on modify mem color.
2- Added update memory button.
Now you can update memories parameters clicking on update mem.
Many tnx for all, Roberto.
Many tnx for your work. But, I am one problem with your last patch.zip 1.72: is impossible to upload from Adalm-Pluto DATV Controller. You have any solution?
73,s de Jabi, ea2aru.
Hello Jabi, it is likely that the filename is incorrect.
With windows normally you have to rename only the title without the extension, as it inserts it by default, otherwise you will get a file that ends with .zip.zip. or delete the old patch.zip file from the download folder and retrieve the patch; in this way it will be saved directly with the correct name
If you still have problems let me know.
El archivo esta bien. Patch.zip. Pero no me carga ...
Una vez que se ha cargado un archivo con un nombre incorrecto en PLUTO, no se puede cargar más.
Primero tienes que borrar el incorrecto archivo directamente en el PLUTO con Putty para que haya espacio nuevamente ...
Hello Jabi, check that you have not inserted video files for static beacon that if large, do not leave room for the patch.
You can delete everything from the patch itself or if you prefer to SSH with Putty and give this command:
# rm -f /mnt/jffs2/*
Then try to load the ptch again.
Check the name it writes to you after you select the file.
If the file differs from patch.zip all lowercase is not accepted
IS0GRB Pluto DATV Patch v.1.8 available:
1- Inserted the buttons for modifying the power.
In addition to the slider it is now possible to modify the power with the + and - buttons by setting the step of 0.25, 0.50 or 1dB or the combination of them up to a maximum of 1.75dB.
As with the slider, the power is changed immediately after the click on the button.
2- Added the config section for the Wi-Fi interface
Now it is possible to easily configure the Wi-Fi interface with SSID WLAN, Password WLAN, Static IP WLAN and Wi-Fi Default gateway.
3- Added some options for the spectrum.
Speed change, color change and fullscreen
4- Move different configurations to a separate page of config. Link at the top of the controller page
5- Changed the formatting of the controller page when it is reduced to 950px on the screen to have different windows on the desktop
Good morning. This is my patch 1.8 compatible with the Adalm Pluto Rev-C.
I would like to thank Nico ON7NDR for the availability, testing and debugging to fix the problem to make my patch compatible with Rev-C and allow him to operate in DATV again.
Please use this version only with Adalm Pluto version C:
In the next versions i will try to do a self-recognition of the Pluto version in order to have a single version.
Thankyou for an excellent patch!
I am using 1.8 with F5OEO Firmware V0201
Now have control of all settings.
Superb results with a GTX 1050Ti graphics card.
Also have an encoder box ON-DMI-16D which I have not been able to get to work.
It’s properly me doing something wrong.