Will try it, thanks
@Ernst
I had to select - 7200 8APSK BW: 2700hz - to turn the RX sync to green
Will try it, thanks
@Ernst
I had to select - 7200 8APSK BW: 2700hz - to turn the RX sync to green
Display MoreHi Ernst,
Go to "SETUP", select the audio device carrying RX audio (VAC in your case).
Bring the volume up to about the level shown in the picture below.
Tune your rx to make the signal fill the "Tuning Window", with the leftmost peak centered in the "Ref" column. The circle should show a constellation like in the picture.
Go to "File", wait for the button " Open received HTML file" to show up. Click on it and have your browser display incomming data.
73, Martin
On windows 7 this will not work, that was my other problem
On windows 7 this will not work, that was my other problem
Works on Win7 here, so should work on your pc too.
Works on Win7 here, so should work on your pc too.
maybe something to review here, It wouldn't show the constellation window for some strange reason
maybe something to review here, It wouldn't show the constellation window for some strange reason
Turned out a volume mixer issue, still the performance under W7 is nothing compared to hsmodem running under W10, the 5 files and the html were transferred successfully on W10 but not on W7.
Good afternoon to all: Any trick for work with IC-9700 ? Any have aucun reception trck?.I have read the doc for the ICom but notihng with V0.87 .Regards de Jabi, ea2aru.
EA2ARU There is no Trick. Connect the input of your soundcard to IC9700
ACC1 , Pin 2 (GND) Pin 5 (Signal).
OR to Speaker out (not recommended, but will work)
OR to headphone out (not recommended, but will work)
Goto hsmodem SETUP, set RX to your soundcard input. Tune your IC9700 RX-frequency until you see the constellation like in post #59 . Follow the instructions in post #59.
Also, carefully read instructions in your manual about the speaker configuration in chapter [EXT-SP MAIN / EXT-SP SUB] if you connect to your speaker output.
EDIT: Additionally, check the manual provided by Amsat (see next post) if you want to use USB SOUND features for RX and TX with ICOM Transceivers.
73, Martin
The manual for the AMSAT-DL High Speed Modem Sofware is available below in one PDF file.
The multimedia high-speed modem is used for fast digital data transmission in a max. 2.7 kHz wide SSB channel as used with the new MM-Beacon on QO-100.
Manual is here: http://dd1us.de/Downloads/Manual%20HSModem%20rev%202.03.pdf
Hello:
I have a problem with high speed modem.
When starting everything runs normally,but after 3 to 4 seconds the modem loses the IP address and gives me an error massages.
Can someone give me some advice on what that could be.
73,s de Jabi, ea2aru.
Hi:
I have the error:
...
start Thread
accepted client 0 1396
Connection opened, client: 1396 | addr: 127.0.0.1
1 users logged in
remove client 0 1396
[proceso terminado con el código 3221226505 (0xc0000409)]
...
Any solution, please?
EA2ARU Please more info. Is it Windows or Linux?
The beauty of running this under Linux is: There is no virtual audio cable.
See the picture , it is gqrx and hsmodem running on a ubuntu ( Lubuntu , that is). The audio device gqrx delivers audio to is the soundcard, the capture device for hsmodem is MONITOR output of the soundcard. 73, Martin
Display MoreHi:
I have the error:
...
start Thread
accepted client 0 1396
Connection opened, client: 1396 | addr: 127.0.0.1
1 users logged in
remove client 0 1396
[proceso terminado con el código 3221226505 (0xc0000409)]
...
Any solution, please?
This sounds like the same problem we discussed via the sat the last days.
I posted it in the HSModem Thread some minutes ago:
And no, we have no solution yet.
It happens on WIn10 und on Linux for me, too
An intro video from Kurt DJ0ABR is now available on YouTube with german audio, but hopefully english subtitles will be available when YouTube created them automatically: