I have a 2.6" Digole display for my minitouner and search for a bezel. Do anybody know if there is one available or if there some stl files for 3d printing ??
vy73
Elmar
I have a 2.6" Digole display for my minitouner and search for a bezel. Do anybody know if there is one available or if there some stl files for 3d printing ??
vy73
Elmar
I have a 2.6" Digole display for my minitouner and search for a bezel. Do anybody know if there is one available or if there some stl files for 3d printing ??
vy73
Elmar
Hi Elmar,
bezel for which kind of housing?
73
Rainer
I have a case like shown here:
https://de.aliexpress.com/item…042311.0.0.11086c37FXPGME
On backside I have the Antenna/USB/power plug.
On frontside in the middle I would like to mount the Display , on the on left side power switch and power LED and on right side the LEDs for USB and LNB.
If you ever seen a case where I made a square hole i.e. for some conector you would know why I would like to use bezel or frame.
It should cover the border of the hole and make sure there is a proper distance between the metal front and the circuitboard of the display.
With google I found some for the 1.3" Oled or 2.2" LCD from Digole but not for the 2.6"
73
Elmar
Hello!
Can i use an unmodified LNB for RX only on the MiniTiouner?
Which LNB would you prefer for it?
Thank you!!!
73's Andi
Yes, you can
I use currently a Venton single LNB, same I use for NB. But as I would like to use both in parallel I will chang to another LNB soon.
Only I had to do was to change the LO settings in the software from 9750MHz to 9750,45MHz like I did it in SDR Console. Without this change I wasn't able to RX signals with < 500KS.
73
Elmar
DD0KP Danke für die Antwort Heiner! Kann ich diesen LNB ohne Modifizierung für den DATV Empfang mit MiniTioune nehmen? Im Datenblatt steht ein Empangsbereich von 10,7-12,75GHz und wir haben ja 10,49GHz...
Thank you for your answer Heiner! May i use the LNB out of the box for DATV-RX on MiniTioune? The datasheed says RX 10,70-12.75GHz and we have 10.49GHz on QO-100...
ja das geht bei mir ohne Modifikation des LNB.
Heiner, was ist mit 250 oder niedrigerer Symbolrate. Ich hab da bei unmodifizierten LNB´s Probleme. Geht das bei Dir runter bis 35ks ?
Yes this works Robert..
DD0KP Sorry new to this, how do the LNB's work if they only require 12Volts to be either H or V ?
Hi,
quite easy, this LNB has NO internal switch and delivers H low, H high, V low and V high, each on a single F connector.
So one connector for NB and one for WB.
For distribution in a house you need an external multiswitch.
Ahh OK thank you but what is the advantage over a 12/18v switching type?
Apart from the disadvantage of having more than one Co-ax going to it, holes through the wall etc. You could run one co-ax from vertical polarisation to a receiver for SSB and one co-ax for horizontal polarisation for DATV stuff, so in theory you can have two receive systems at the same time, there is no need for a 18 Volt PSU or buck up converter to get the voltage from a standard 12-13.8 Volt psu.
Typically if you have a 4 co-ax/connector lnb, it gives you the opportunity to modify it and feed with an external gps locked source for ssb RX and still have a V and H output.
All that being said I still run a standard un-moddified single port lnb.
Adrian
Thanks Adrian I guessed as much.
Where can i buy a MINITIOUNER-PRO-V2???
I cant find it...
I know the forum search function and this link!
But it is out of stock in this shop!!!
So i wrote my question...
Then it is useful to provide the information that you already know that link....