Hello Roberto,
Still not possible to stream.
I have access to your Pluto.php, can use it, but still stream failure....
I try still to stream to the Ethernet ip in which pluto.php is running (192.168.20.xxx)
73s de Robert
Hello Roberto,
Still not possible to stream.
I have access to your Pluto.php, can use it, but still stream failure....
I try still to stream to the Ethernet ip in which pluto.php is running (192.168.20.xxx)
73s de Robert
Roberto, yes, maybe.
my txt file commands "route add -net 0.0.0.0 gateway 192.168.2.10",
think this is the problem, I don´t need this gate.
will try ...
Robert
Hm, streaming did still not work.
tried it after reset now 3 times.
I can use your pluto.php, IP adress is ok.
But no streaming possible...
After reset, the pluto.php from the flash works still fine ...
Robert
Yes, Roberto,
your update looks good.
Your update did not change the IP adress in the config.txt ?
I do not use the USB-> Ethernet option what described in #12
I use a real USB to Ethernet adatper
73´s de Robert
Hello Roberto,
my Pluto is at the dish connected via ethernet.
I can install your Pluto_mods-IS0GRB-15-08-2020.tar.gz,
if I run runme1.sh seems all ok.
Your pluto.php script is running.
But, its not possible to transport the stream. Analysis windows is empty.
Maybe different IP adresses?
My Pluto is running a typical IP Adress from the home network ...
73´s de Robert, DD4YR
Hi Roberto,
it did not work here.
Maybe the micro USB female plug is only for DC supply and not wired for Data
did you have tried it, and still working?
How will Pluto difference two USB Slots ?
Robert
it is possible to use the Y-shaped OTG cable described in this guide
Hello Roberto,
did not understand how to?
I think, the PLUTO can only solve one USB port at the same time ...
73´s de Robert
Hello Piotr,
you have to copy the pluto.frm (beta for the brave Version) on the Pluto during Pluto is connected via USB like a USB-Stick.
If the pluto.frm is copied, you have to remove the Pluto drive as follows:
Klick on PlutoSDR (D:) auswerfen! (second line !!!, first line will remove but not install the firmware!)
Then the Pluto will be disconnected and installing the firmware.
The blue LED is fast blinking.
This Firmware change need some minutes, don´t be wory ......
After firmware change the Pluto Drive will be back, and pluto.php is on the drive available.
Yo do not have to disconnect the USB cable at any time !
73´s de Robert, DD4YR
you start the html file.
Try 192.168.2.1/pluto.php
If it does not start, the firmware isn´t installed ....
73´s de Robert
no,
I wrote yesterday Wolfang a email, but he did not answer yet ....
Maybe vacation .... we have to wait.
73´s de Robert
Ich werde jetzt mal weiter testen und Berichten.
Ja, Ulrich, das interessiert mich.
Im Moment mache ich das noch über eine WiFi Brücke, ist halt ein zusätzlicher WiFi Empfänger am Pluto den man sich ggf. sparen könnte.
... Can we tell them which is the fault or not?....
Not sure that the display is faulty.
Wolfgang, DC2TH, told me, he had similar problems.
mayby a problem from the Minitiouner
We have to check more ....
Ok,
habs verstanden. Danke für die Info!
Also, wenn ich in meinem Pluto in die config.txt die Daten eingebe und speichere bleiben sie nach Neustart (USB Gerät auswerfen)
erhalten.
[WLAN]
ssid_wlan = Gastzugang
pwd_wlan = nurfuergast
ipaddr_wlan = 192.168.20.194
Leider hab ich keinen solchen Stick um das auszuprobieren
73´s de Robert
Hm,
ich verstehe Dein Vorhaben noch nicht ganz. Der AC430 ist doch gedacht um ein Gerät auf welchem Windows läuft auf aktuelle WiFi Standards zu bringen. Dazu sind doch Windows Treiber erfoderlich.
Diese Anforderungen erfüllt doch der PLUTO überhaupt nicht.
Robert
Thats what i thought,
this dish is useful for your project.
The mesh is fine enough and usable for 10 GHz., 2,4 GHz in any case.
Also usable for DATV ....
take it...
73´s de Robert
Oh,
an diesem *.stf hätte ich Interesse
73s de Robert
do not use a mash dish
not in any case!
There are fine mesh dishes wo are also suitable for 10 GHz.
We have to take a look at the product that was offered.
Do you have any technical data from this mesh dish offere?
Robert
Mit welchen Signalstärken sollten bei optimaler Ausrichtung die CW-Baken und die PSK-Bake reinkommen?
Das ist relativ.
Schalt besser mal auf H (18V) und schau nach der DATV Bake wie viel sie sich vom Rauschen abhebt. Dazu die Bandbreite auf 3MHz oder so erhöhen. Wenn man den linken Bereich der DATV Bake anschaut, dann sieht man auch bei Horizontaler Polarisation die NB Signale durchzucken. Das LNB dann im Squint so weit drehen, dass die NB Signale möglichst nicht mehr zu sehen sind.
Dann stimmt auch der Squint Winkel vom LNB.
73´s de Robert
ALs LO gebe ich 9360 MHz und die Bakenfrequenz mit 10492
Polarisation Horizontal / 18V eingegeben?
FEC auto ?
Also, die Bake mit SR1500 ist ausreichend stark um auch mit 70cm offset Spiegel zu empfangen.