Hi Edu, for the pa, I can advise you to contact IU6DEV (Andrea)!
He made one and I think it went very well!
Posts by iu4gav
-
-
Ciao, penso di aver capito bene, te vuoi sapere se puoi eliminare oppure no l'attenuatore da 5db, ma se non sai quanta perdita ti creano i codini, non puoi avere risposta alla tua domanda!
-
Come sempre.. ottima spiegazione quella data da Alessio!
Mi permetto di aggiungere che, quello che te non hai considerato, "le perdite dei cavetti" non è roba da poco!
Trovarsi una perdita di 1 db in un cavetto, è roba da ridere! (vorrebbero sempre testati!)
73
IU4GAV
Andrea
-
Ok, ho visto la tua mail, felice di poterti aiutare
-
Blocca la frequenza con il sistema "Geostationary Beacon"
-
ok thanks for the info, I thought it was a problem with my pc!
-
Maybe it's just my problem, but in rx when I change signal, I have to close and reopen the script, otherwise it doesn't decode anymore!
basically when the signal changes, it doesn't update my flow!
Does this happen to anyone else?
How did you finally solve it?
73
IU4GAV
Andrea
-
okay! downloaded! Tnx!
-
ok perfetto, appena disponibile proverò anche il mio i9 13th!
-
OK thank you! alora I have to figure out how to go to tx!
-
hello, is it a version only for rx, or also for tx?
-
It seems to me a good decryption software alternative to minitioune, except that:
1) below 66 ksr it does not decode, by choice of whoever made the software! (in the source file the 35 ksr is set wrong and the ksr below 35 are not managed at all)
2) it would be good to have the threshold level to check if you are transmitting enough to be decoded or if you are low on power!
3) in the Mer you need decimals, which would be fundamental if you decide to use open-tuner to point the dish!
73
IU4GAV
Andrea
-
Tnx. Tom! :pollice in su:
-
Display More
Petronel,
from 10MHz OCXO (squarewave) you can extract 50MHZ harmonic with crystal and buffer this with inverters and feed into pluto.
Divided by 2 can be used for LNB!
Found this somewhere, do not remember where.
25MHz for the pluto is out of spec as far as I remember , might work or not.
In a second step you may sync the OCXO to GPS ...
... always good to have enough ham projectsI do not recommend to remove original TCXO because you have to apply a lot of heat. Disable it by EN input and place the new TCXXO elsewhere on a small PCB.
As per the document, the pluto supports colck from 10 to 80 mhz!
-
Hi, at the moment I'm going with reference to 25 mhz, I've tried both with gpsdo and with tcxo, and it's absolutely not bad!
-
No , mi dispiace, ma essendo un amplificatore a 2 ghz, ci devi lavorare un bel po' per portarlo a 2,4 ghz!
-
All F5EOE firmwares have the same name, so I’ve never been able to know which version is which. Neither can I find an authoritative website with all the versions to download from. My approach has been to suck-it_and_pray. I’ve no idea which version I have working right now. If you figure it out a better way, please let me know.
Hi, if you need the F5OEO firmware, I can pass them to you!
-
Thanks Benno, if you still haven't solved it, can you share your problems here?
73
IU4GAV
-
Hi Robert, in the meantime I have to tell you that I am pleased to hear from you here, which means that we have an exchange of ideas, which is always productive!
I was not aware that an "APPLY" was a problem for the pluto!
Ps.
Have you tried the PTT with firmware 2202 and Patch F5UII?
-
Hi Benno and Robert, I didn't think anyone used the PTT button, because if someone, like me, has mounted the ptt board inside the pluto, with the latest patches released in August by F5UII, one for firmware 0303 and the other for previous versions, the relay works automatically when you go to TX.
I didn't know Dominique knew about it!
PS.
I like to be comfortable, and everything he can do automatically, I don't do it by hand!
