Dominique:
Good morning. Would it be possible to reprogram un the DATV-Easy (2.17) the power output setting ( 0 to 100) more finely? For example, increase by 1 by 1, or 5 by 5, etc, or directly increase the power. The are problems with the fine running .
73, a de Jabi, ea2aru.
Good morning:
I am looking one Minitouner Pro 2. If you have aucun for sale, please send me one email to: Jabieraru@gmail.com
73,s de Jabi, ea2aru.
What modes are worling for send and receive SSTV on QO-100? What software? 73,s de Jabi, ea2aru.
Thanks for the answer George:
I've been trying to get GNU Radio up and running for several years. What version do you use for Windows 11? The 3.7? Which do you recommend me to go down? Do you have any manual to start? I've searched the internet and I get lost...
Happy natal for you and yours de Jabi, ea2aru.
Estimado George:
If it is possible, please, send me direction for download a good GNU radio software, and your configuration for RX/TX to QO-100 ...
73,s de Jabi, ea2aru.
Good morning again:
If it is possible, please, send me the "
| PLUTO v32 | pluto.frm 1602 (F5OEO) |
I am looking difrents software versions for my Adalm-pluto Rev. C.
73,s de jabi, ea2aru-ç.
P.D.: jabieraru@gmail.com
Hi Dominique:
I am Jabi, ea2aru, and I am be very interesed in one copie of new Easy
2.06 for test it. I am writing articles for the spanish asociation of
radioamateurs (URE) revue. If it is possible, please, send me one copie.
73,s de Jabi, ea2aru.
Hi Dominique:
I am ready for work how tester for new versions.
73,s de Jabi, ea2aru.
Hi:
I have the error:
...
start Thread
accepted client 0 1396
Connection opened, client: 1396 | addr: 127.0.0.1
1 users logged in
remove client 0 1396
[proceso terminado con el código 3221226505 (0xc0000409)]
...
Any solution, please?
Hello:
I have a problem with high speed modem.
When starting everything runs normally,but after 3 to 4 seconds the modem loses the IP address and gives me an error massages.
Can someone give me some advice on what that could be.
73,s de Jabi, ea2aru.
Good afternoon to all: Any trick for work with IC-9700 ? Any have aucun reception trck?.I have read the doc for the ICom but notihng with V0.87 .Regards de Jabi, ea2aru.
Hi George:
Not problems with work in full-duplex mode. If it is possible, pleaae, send me code for work and paly with it.
73,s de Jabi, ea2aru.
Good morning: I am be very interesed in your work. Is possible, please, send instructions for work ( and play) with this mode?
Regards de Jabi, ea2aru.
Good morning:
If it is possible, pse, snd me tha last version. I have lost it.
73,s de Jabi, ea2aru.
Good morning:
If it is possible, please send the last version to my emil for test it.
73,s de Jabi, ea2aru.
Markus ?????
To Markus:
Yo have one PCB or assembled unit? I am be very old for ensamble...
73,s de Jabi, ea2aru.
Ok tony. All is working 100% ok again. I have instaled "new" the software and all is ok.
73,s and bon natal for you and your family de Jabi, ea2aru.
Dear om:
I am working (and playing) with the last version. with Adalm-Pluto. But I have one qestion: not is possible set Modmode fixe to QPSK 4/5 to see only the QO-100 DATV?
73,s de Jabi, ea2aru.
