Does anyone know, where the focus point of the Venton lens ist?
As far as i remember, the PE1CKK lens has it about 11mm towards the dish...
Does anyone know, where the focus point of the Venton lens ist?
As far as i remember, the PE1CKK lens has it about 11mm towards the dish...
Different lenses/material have other phase points , so I agree with DD4YR 's remark .. try to tweak the LNB position to max signal (to noise ratio)
Yes, you are both right, but it is physically not possible in my setup to bring the lens into the optimum focus.
So in my setup the EXL-T lens gives a better result...
Tnx for report,
Did you adjust or correct the focus point between the two lenses?
And when yes, what was the difference in mm?
73´s de Robert, DD4YR
Unfortunately no. No possibility to go further backwards, the reflector hits the mount.
So in both cases I would say, that i am a bit out of focus towards the dish...
Please compare with rocket and post-results
Same POTY feed, same LNB (GM201new), different lenses: Venton EXL-T vs. PE1CKK Polyamid lens.
The Venton EXL-T lens gives a 3dB better S/N at my dish (Kathrein CAS80 f/D about 0.66).
73, Thorsten
Today i tried to decode DATV with version 2.0.14.
First I tuned to the beacon, and played around with the "Carrier Recovery" until i got a proper IQ plot, sync_confidence raised to 32 and the buffers raised to 8192. At the moment, the buffer reaches 8192, the program stopped and closed.
Then I tried some other signals. Tuning and carrier recovery went well so far, IQ plot looks fine, sync_confidence raised to 32 and stayed stable, but the buffer stayed at 0.
No decoding was possible...
Any ideas?
Tnx. 73, Thorsten
Edit: In the meantime I sucessfully decoded the beacon (just a wrong streaming parameter in VLC). But the second problem stays... Decoding of the other signals works too. VLC stream must be restarted, then decode begins...
2.0.14 is available under http://5.181.50.78/dvb-s_gui_amsat.zip
Display MoreI order a Venton EXL Twin for the mod of Bamatech.
Take of the lense, was not a problem. Try to fit it to the Bamatech Duo Fed but it don´t fit
Measured the inner diameter of the Bamatech with 18 m/m
Measured the inner diameter of the Venton with 18,7 m/m
Looks good but don´t fit together. Test of Bamatech with this lense not possible.
73 Joachim
I would use the "poor man's lathe", a simple needle file and go round and round to get the 0,35mm off.
Needs a bit of care and time, but will work...
You could sell a few hundred of these ABS-covers among the readers/POTY-owners on this forum I think
I would bet, yes (but not my intention).
The 3D models (FreeCAD and STL) are available at https://github.com/dl9sec/POTY_Parts...
73, Thorsten
Now i have a direct comparison of my BaMaTech feed with BaMaTech lens and modified LSP-02G LNB (external reference) to a POTY feed with Venton EXL lens and GM-201 LNB (new version, also modified for external reference).
The GM-201 with Venton lens gives about 8dB more S/N than the LSP-02G with BaMaTech lens...
Also hier mein POTY mit ABS-Haube fertig silikoniert und montiert...
The translation is a bit misleading and not, what I intended to say.
The patch will be tuned with/for the ABS cover (currently printing)...
Hier der PLA-Prototyp meiner POTY-Haube. Wird in den nächsten Tagen in weißem ABS gedruckt und der Patch dann damit abgeglichen...
Ist aus Polyamid (PA)...
Also die neue zylindrische, gedrehte POTY-Linse bekomme ich bei Hans Holsink PE1CKK (pe1ckk@hetnet.nl). Er gibt sie für €5 + Versand ab...
Hallo Peter,
vielen Dank für die Info.
Für meine BaMaTech habe ich ja bereits eine Linse.
Nun bin ich auf der Suche dach der neuen zylindrischen für den POTY (tatsächlich habe ich mir als Plan B vorsichtshalber bereits mal ein Venton mit Linse und Adapterring zum Ausschlachten bestellt. Mal wieder ziemlich ähnliche Gedanken gehabt ).
73, Thorsten
Doch kleben geht schon (Spezial-Aktivatorprimer+Cyanacrylat oder 2K-Spezialklebstoff auf Basis Methyl-Methacrylat), aber wie schon gesagt, den richtigen Kleber zu bekommen scheint schwierig zu sein.
So schön die Eigenschaften von PP sind, das Zeug zu kleben ist Horror...
Ist fast wie mit PTFE, da hält auch nix dran......außer natürlich Pfannen
Aber ich glaube, wir sollten das Klebethema nicht zu sehr strapazieren, ursprünglich gings ja um den Wetterschutz...
Also wenn es HT-Rohre (die mit den Gummidichtungen drin) sind eigentlich PP-H.
Ich seh schon, beim nächsten Baumarktbesuch muss ne Tube Tangit mit
Danke für die Info.
Ich kanns mir aber irgendwie nicht erklären, wie dieser Kleber PP kleben soll. Kleber für PVC-Rohre (Schwimmbadtechnik, Abwasserrinnen usw.) funktioniert für gewöhnlich nicht für PP/PE.
So gut wie alles sieht vermeintlich geklebt aus, lässt sich aber wie Folie davon abziehen.
Eine gewisse Haftwirkung gibts schon, aber ich glaube, das elektrischen Äquivalent wäre die kalte Lötstelle
Egal, hauptsache es hält...
73, Thorsten
Kennt jemand eine Bezugsquelle für die neue zylindrische POTY-Linse aus vernünftigem Material gedreht?
Beim Bausatz von IBJ ist leider nur eine gedruckte PLA-Version dabei...
Vielen Dank.
73, Thorsten