Hi,
the AD 9363 data sheet says
Reference clock Input Signal Level 1.3 V p-p AC-coupled external oscillator
That is the typical value, no min or max given.
Detlev
Hi,
the AD 9363 data sheet says
Reference clock Input Signal Level 1.3 V p-p AC-coupled external oscillator
That is the typical value, no min or max given.
Detlev
It seems to be 2.6 kHz. I hoped the spacing would help to find the source, but 2.6 kHz is very strange.
Detlev
What is the distance of the interference lines?
Hi,
I suggest to add an attenuator. That is the simplest method to see if something changes.
Detlev
Hello,
which size is your dish? I use a 60 cm dish without any problems. A 10 dB attenuator or 740 MHz filter has no influence.
Detlev
I am going to use a 10 MHz OCXO (Bliley NVG47A1282) , a Si5351 Synthesizer which produces 40 Mhz and 25 Mhz for the LNB and an Arduino nano.
No, not yet. I'm still waiting for my U.FL-SMA cable and the external clock isn't ready .
Hallo Geri,
wie geht das? Hast Du einen Pluto mit Ethernet-Anschluß?
Gruß Detlev
Hi, here you can see how to communicate with your Pluto:
The moment you toggle to an extern clock and there is none, the Pluto will stop and will be no more accessible until you connect an extern clock.
Detlev
Hi,
you find the answer here: https://wiki.analog.com/university/tools/pluto/devs/booting
0.32 | C | refclk_source | external | Reference Clock on u.FL is usedad936x_ext_refclk_override holds frequency in Hz |
||
|
Hi, I ordered 5 cables U.FL to SMA (10 cm) with eBay:
5x Stecker SMA Buchse Auf Ufl / U. Fl / Ipx / Ipex RF Coax Adapter RG178 Kabel
Hi Ansgar,
you transmit on 2400 MHz and receive on 10500 MHz, where is the 11 kHz shift?
Detlev
PS Do you use a Leo Bodnar GPSDO?
Digital PLL allows main output reference frequency to have almost any value between 450Hz and 800MHz.
The second output frequency depends on the first output due to a common internal clock, if you need individual flexibility, multiple mini GPS units may be a better choice. If both outputs have the same frequency their relative phase shift can be adjusted. This can be used, for example, to generate two signals with 90° phase shift for use in I/Q mixer.
Hi Adrian,
You are right, maxcpus works, but if you ask printenv maxcpus, maxcpus is not defined.
You have to differentiate between internal and external clock. Ansgar speaks of an external one
Detlev
Hi Ansgar,
you use the command for the internal reference clock.
I recommend reading: https://wiki.analog.com/university/tools/pluto/devs/booting
The command:
Detlev
Hallo Raimund,
auf der Platine ist eine kleine Steckverbindung (U.FL) CLK IN, die max. 14,3 dBm 3,3 V pp verträgt. Das passt zu Deinem GPSDO. Du musst jemanden finden, der die eine zusätzliche SMA Buchse in das Pluto Gehäuse einbaut und die Verbindung von der Leiterplatte zur Buchse herstellt. Die Umschaltung auf den ext. CLK wird per Software gemacht, alles dazu findest Du auf der Analog Device Seite, auf die hier im Forum unter Pluto Rev. C hingewiesen wird.
Ich empfange z.Zt. nur mit dem Pluto, LNB und Pluto unstabilisiert und binde die SDR Console an die Mittelbake an. Zum Senden benutze ich ein FT-818 mit dx-patrol Upkonverter Mk. 2 (Achtung: bei Vollaussteuerung unerwünschte Seitenbänder im Abstand 48 MHz!) und einer 20 W Endstufe von PE1CMO. Der Upconverter wird mit einem OCXO synchronisiert.
Ich hatte versuchsweise hinter meinem Pluto den 1 W Verstärker von AD CN0417 angeschlossen und bekam etwa 40 W Ausgangsleistung, viel zu viel. Als Antenne habe ich einen 60 cm Spiegel und eine selbstgebaute Helix mit 6 Wdg.
Kurze Kabel U.FL mit SMA Einbaubuchse gibt es bei eBay
Viele Grüße,
Detlev
Hallo Uli,
die Frequenzerzeugung ist im Datenblatt des AD9363 beschrieben. Wenn Du die Mittelbake zur Synchronisation benutzt, kann nicht unterschieden werden, wo die Frequenzabweichung herkommt, vom Pluto oder vom LNB, der Pluto kennt den LNB ja nicht. Er wird nachgestimmt und verändert somit auch die Sendefrequenz.
Viele Grüße,
Detlev
Hallo Raimund,
welche Pluto-Version hast Du denn bekommen? Wenn es Rev. C ist, brauchst Du nichts umzubauen, da ist der Anschluß für einen ext. Clockeingang schon drauf.
Frohe Ostern,
Detlev
Hallo,
ich habe am 25. März bei DigiKey einen Pluto bestellt und am 29. März die Rev. C geliefert bekommen.
Frohes Osterfest,
Detlev