AMSAT-DL Forum
Recent Activities
-
DL3ED
Replied to the thread Pluto-Treiber.Postmoin,
der einpolige Schalter reicht ja aus wenn die Z-Diode drin ist. Bei 12V kann die (Led 18V) ja nich leuten da die Z-Diode drin ist und der Schalter die (12V Led) gegen Masse schaltet und leuchtet. Schaltet man auf 18V ist die (12V Led) aus und da… -
PY1SAN
Reacted with to DJ7TH’s post in the thread DATVEASY problem.Reaction (Post)Hi Guenter,
DATV Easy does not access the device driver directly, but receives the video and audio data from OBS via virtual cam and possibly the audio data via virtual audio cable, depending on the OBS version.
More details on how to handle the various… -
HB9SKA
Replied to the thread Pluto-Treiber.PostHallo Ulrich
[…]
Dann würde ich einen 2-poligen Umschalter nehmen und die LEDs mit ihren Vorwiderständen über den 2. Pol nach Masse/Minus führen. Beim Umschalten brennt dann die entsprechende LED. -
VE4SW
Reacted with to HB9DUT’s post in the thread Kuhne MKU UP 2424 with low power IF.Reaction (Post)Hallo zusammen
hat jemand von euch schon Erfahrungen mit dem Umbau des Kuhne MKU UP 2424 auf low power IF?
Die Idee dahinter ist den Konverter mit der Steuerleistung von 0dBm aus einem Transverterausgang anzusteuern.
Für den MKU 13 G3 hat Kuhne selbst eine… -
DJ7TH
Replied to the thread DATVEASY problem.PostHi Guenter,
DATV Easy does not access the device driver directly, but receives the video and audio data from OBS via virtual cam and possibly the audio data via virtual audio cable, depending on the OBS version.
More details on how to handle the various… -
DL8EBD
Reacted with to SP3OSJ’s post in the thread New TRV for TRX.Reaction (Post)Hello everyone
I thought to make a new TRV for TRX (HF/VHF).
First, I drew a schematic.
I used dual SAW filters (SF2173E and SF2124E) to accurately get the frequency of 2.4GHz , without any other signal mixing. I used a low-pass filter in the PA. TRV seeded… -
SP3OSJ
Replied to the thread Pluto-Treiber.PostDie Verwendung eines 100kHz DC/DC-Wandlers (MC34063 - Driver Amplifier)
) ist für den Empfänger nicht geeignet. Oberschwingungen alle 100kHz stören den Empfänger. Es ist besser, einen DC/DC-Wandler mit einer Frequenz von 1MHz (MP1584) zu verwenden und… -
PY1SAN
Reacted with to DL1AQ / HS0ZQO’s post in the thread Pluto Plus Erfahrungen.Reaction (Post)Hallo,
ich habe mir den Pluto Plus für den Betrieb über QO-100 zugelegt. Zwei Gründe sprachen für den Pluto Plus: 1. Die Frequenzstabilität und 2. Der Pluto Plus hat schon einen Ethernet-Anschluss. Ein erster (Empfangs)Test lief relativ erfolgreich:… -
PY1SAN
Reacted with to HB9DUT’s post in the thread Kuhne MKU UP 2424 with low power IF.Reaction (Post)Hallo zusammen
hat jemand von euch schon Erfahrungen mit dem Umbau des Kuhne MKU UP 2424 auf low power IF?
Die Idee dahinter ist den Konverter mit der Steuerleistung von 0dBm aus einem Transverterausgang anzusteuern.
Für den MKU 13 G3 hat Kuhne selbst eine…