the time was ok, but i Txed on 630.
regarding the description to build your dualband patch antenna:
There should be a note "not" to use N-connectors.
If the feed is aligned in the focus, then the N-plug is almost in the same place as the LNB holder of a standard dish. No chance to screw on the cable connector. With SMA it is no problem.
For non-standard dishes or home made LNB-holders it may work also with N-connectors.
I would like to use my Spectrian SSPA for DATV via QO-100 and I am looking for a suitable heatsink: any suggestion/hint?
I am also looking for the way to calculate it myself...
Claudio, if you talk about the 75W spectrian PA, just an approximate calculation:
It is specified for 75W output at 26V / 17A DC input.
The power loss (to be cooled) is 26*17 - 75 = 367 watts.
If you have an ambient temperature (in Italy) of i.e. 30 degC, and you allow the amp to get a max. of 60 degC, then you have a temp difference of 30 degC.
The cooler you need should have 30 / 367 = 0,08 K / watt.
A cooler with a thermal resistance of 0,08 K/W is a real big one. You will usually need one or more cooling fans to achive that value. Or if you have enough space you can do passive cooling.
As an example of a cooler without fan:
or with fan:
if you choose the maximum cooler temperature, please take into account that the chip (the chip inside the transistor) gets hotter then the cooler. To do an exact calculation you need to check the datasheet for the thermal resistance of the transistor, the mounting ... This is sometimes difficult to calculate, so a good reserve is needed.
73 de Kurt
I agree it is generally not possible to reverse calculate the thermal resistance from chip to outside casing of an amplifier. It is hard to do accurately even as the designer of the amplifier. I would guess that for a professionally built amplifier, unless you have the manufacturer's spec to hand, then 60C maximum baseplate temperature is a good figure to aim at.
I have also used water cooling of SSPAs with great success. It is not too difficult - a copper block with copper pipe soldered to it and a bucket of water and fish tank pump works pretty well, but I have not measured the thermal resistance of this.
I have also used water cooling of SSPAs with great success. ...
I am also a great fan of watercooling. Did it for my SW 1kW amp and it works very well.
In this case I have the problem that the 13cm PA is mounted at the dish which makes it hard to install a water cooling, but it would be nice to have
(just discovered that the status of my upconverter-order in the Amsat shop changed from waiting to finished. This makes me very happy, I'm looking forward to the first QO100 qso).
It is not so EH2 related but i also own a water cooled amplifier.
Its from an old Coherent DEOS Lasersystem, delivers easily 1,2KW on VHF.
Supply voltage is 48V so not usable as "portable" amp, not to forget the needed chiller.
1K2 looks much on VHF but compared to the bigger Laser RFPSUs (E1000) with >10KW at my QRL this is a tiny amp
I only fired it up once on a dummy load, because neither my coaxcable or antenna can handle this much power.
Friends, which PA do you recommend for broadcasting in WB?
Heiner's link shows a very good paste.
You should set a reasonable quiescent current. There are some descriptions in the net talking about 2A per mosfet. This is too high and results in a very hot board needing a huge heat sink.
I am using 0,6A per mosfet (1,8A in total), linearity and gain is ok, and higher current only slightly improves that.
If the +12v- enable pin is connected to the PTT (via a relais), then you can use it for normal SSB with a little cooler in the size of the spectrian board.
This may be different for long transmissions like sstv, but I have not tested that until now.
Just repaired my "small" Andrew MRF21045 PA which quits working after the first few minutes on QO100 on 12.02.19
A broken SMD resistor on the gate was the cause of the failure.
Now its a little bit improved by 1dB and delivers about 15W when excited with the 500mW from the BU500.
Has somebody already modified/tested this Amp on 2,4GHz?
25.04.20 because of not approved commercial use my submitted technical Infos are deleted
DB8TF Did you find a datasheet for the BLD6G22L- 150BN/2?
I could only find the data sheet for the BLD6G22L- 50. which isn't much help for finding the required bias current unless you assume the -150N/2 is 3 or 4 -50's in one package. Also if you put both parts of the chip into class AB will you have to de rate the chip to cope with the lower efficiency?
Also I noticed from your screenshot you had removed two devices on the input? I presume they were filters of some kind?
The board looks good value for money since it comes with a top case and a heatsink - I'm just worried about getting one where the doherty bit is built into the chip with no datasheet
thanks for your description, I also ordered one. How did you solder the SAW filters and the other things out? Next up someone wrote that it is hard to solder because the base plate absorbs the heat strongly. Maybe OH3WE writes us how far he is
with the PA.
… and about the naming i found this: